Browsed by
Tag: receiver

The TRN BT20 2-pin 0.78mm IEM Bluetooth Adapter

The TRN BT20 2-pin 0.78mm IEM Bluetooth Adapter

Hi everyone,

Today, I’ll be reviewing the TRN BT20 Bluetooth adapter for 2-pin In-Ear Monitors (IEM):

TRN BT20 1
TRN BT20 1

The TRN BT20 is a Bluetooth 5.0 adapter that is available in 3 different versions:

  • 2-pin 0.75mm
  • 2-pin 0.78mm
  • MMCX

The version I purchased is the 2-pin 0.78mm for my KZ ZS7 IEM’s.

The adapter syncs together to bring you stereo sound. It uses a Realtek Bluetooth 5.0 SoC that while it is not specified which specific chipset it’s being used, I suspect it may be using the Realtek RTL8763B.

Because of it using a Realtek chipset, it doesn’t support the aptX audio codec, but it does support AAC along with SBC. This means that when paired with an iPhone or Android device, it should use AAC instead of SBC, and for backward compatibility, the SBC codec will be chosen if a device lacks the AAC codec.

Packaging

The packaging is very simple, as can be seen in the following images:

Here, you can see the sides:

And here you can see the back:

TRN BT20 3
TRN BT20 3

To open it, you have to slide the box outside:

TRN BT20 5
TRN BT20 5

Opening the box, both pieces of the TRN BT20 are revealed:

TRN BT20 6
TRN BT20 6

As you can see, they are very well protected and can be easily taken out:

TRN BT20 11
TRN BT20 11

Continuing unboxing the box, we need to take out the cable and manuals which are after taking out the following:

TRN BT20 7
TRN BT20 7

There’s a Micro USB Y-Cable that allows us to charge both Bluetooth pieces at the same time:

TRN BT20 8
TRN BT20 8
TRN BT20 18
TRN BT20 18
TRN BT20 19
TRN BT20 19

Finally, we have the manual, warranty card, and the card that says it passed quality checks:

TRN BT20 9
TRN BT20 9
TRN BT20 10
TRN BT20 10

Using the TRN BT20 with the KZ ZS7

I was using my KZ ZS7 IEMs with a Revonext 3.5mm 3-button cable before using this TRN BT20 Bluetooth adapter.

TRN BT20 12
TRN BT20 12

I removed the IEM from the cable so that I can plug them in the adapters:

TRN BT20 13
TRN BT20 13

Plugging them was straightforward and they are tightly attached:

TRN BT20 14
TRN BT20 14

Fitting

This is a part where these don’t work well with my ears and the KZ ZS7.

This adapter is supposed to be hanged behind the ears:

TRN BT20 15
TRN BT20 15

Unfortunately, My KZ ZS7 doesn’t get sealed in my ear and the TRN BT20 pushes them out, so I’m using them without hanging them behind my ears:

They are not heavy and now my KZ ZS7 seals fine in my ears. I think if TRN releases a version of the BT20 with a larger ear hook, then they may fit better. Otherwise, I don’t have a problem using them this way.

Pairing

Pairing the TRN BT20 with my phone was extremely easy. You just turn it on and it will enter in pairing mode automatically. From there, you can choose it in your phone and it will pair:

TRN BT20 Pairing
TRN BT20 Pairing

Charging

I haven’t yet discharged the TRN BT20 battery entirely, as I don’t listen to music at loud volumes. My Android phone reports 50% of battery left after about 3 hours of continuous usage. The volume is set around 1/4 of the slider and that produces a comfortable audio level to my liking. Past it, and it’s too loud. As mentioned above, the TRN BT20 supports the AAC audio codec which my phone is using. Because of this, charging normally takes around 45 minutes (Remember I have not discharged this completely). I’m not using the supplied cable to charge them. Rather, I’m using the UGREEN Micro USB Y cable:

TRN BT20 20
TRN BT20 20

There’s one side that will always charge faster because one side acts as a receiver while the other is receiving and transmitting the audio to the other BT20 side. I have paired the left adapter to my phone so that one takes a couple of more minutes to finish charging.

Audio Quality

I’m actually surprised by the quality of these. I think, personally, that the TRN BT20 has an advantage given that it uses a Realtek SoC on both sides. This means each side is decoding its own audio channel. This is similar to how balanced DACs work, in that each DAC decodes a specific channel. This has the advantage of improving the sound stage and channel separation. That’s exactly what I’m experiencing with the TRN BT20. The tonality is just awesome.

Because each side is decoding their own corresponding audio channel, I feel this improves the sound separation much like how balanced DACs work, except that there are no cables around.

It’s true that the TRN BT20 doesn’t support aptX nor LDAC, but given its ability to decode AAC, the audio quality is of very good quality. Even using the SBC codec, I find the quality to be amazing.

TRN BT20 AAC codec
TRN BT20 AAC codec with my Samsung Galaxy S9+

There’s a bit of a hiss when used with sensitive IEM’s, but it’s way less than other Bluetooth adapters, especially those that are not using dedicated audio DAC’s in their implementations. The sound quality is not degraded because of this, but I’m sure some may not like the hissing.

Overall, I’m pleased with the sound quality, and I’m using this Bluetooth adapter rather than my USB DACs with their cables.

Compatibility

I’ve been using the TRN BT20 with my Samsung Galaxy S9+, where it uses the AAC audio codec. The sound quality is excellent.

I also tested this with my HiBy R3 and Hidizs AP80 which I use as a DAC and Bluetooth transmitter to transmit my PC audio to the BT20. In this case, the SBC codec is used, as Hiby OS does not support transmitting AAC audio yet, although HiBy replied to a comment saying they may add this in a future firmware.

TRN BT20 21
Hidizs AP80 using in DAC mode and transmitting audio via Bluetooth

I normally set the volume between 7 to 13. Going up, it is too loud.

The only problem I found is that when using some Qualcomm transmitters with Windows, the volume will be extremely loud.

Conclusion

At around $33-34 on Amazon, you can’t go wrong with the TRN BT20. They do not have aptX, but their ability to decode AAC means the audio quality is not compromised.

The use of Realtek on both sides means each side decodes their own channel audio, which can improve the sound separation and sound stage.

There’s a bit of hissing which could be distracting for some, but it’s not very noticeable compared to other adapters.

The battery life is great and will last some hours. Charging should take at maximum 2 hours, but it charges in way less than that, having a 70mAh battery on each side, and charging at about 50mAh, it should take about an hour and a few minutes.

Unfortunately, it’s the fitting that didn’t work for me, but this part is one that depends on the IEM’s being used and your ears.

I’d rate this 4 out of 5, that last star being because of it not playing nice with my ears.

You can get the TRN BT20 on Amazon. Select the version that is compatible with your IEMs:

The Hidizs AP80 just got support for Sony’s LDAC bluetooth audio codec!

The Hidizs AP80 just got support for Sony’s LDAC bluetooth audio codec!

UPDATE 12/29/2018: Video here: https://moisescardona.me/hidizs-ap80-ldac-video

Hi everyone,

Today morning, it came to my attention that there was a new firmware update for the Hidizs AP80 Digital Audio player. I downloaded and installed it, and surprise! We have LDAC support now! This means that it can be used as an LDAC bluetooth receiver and should also work as a transmitted, altough I haven’t tested this mode yet.

To test the Hidizs AP80 LDAC functionality, I tried using my phone but for some reason it doesn’t work on either the HiBy R3 nor on the AP80. This may be a bug on the Samsung Android Pie beta software, or some sort of incompatibility in HiBy OS. Since this didn’t worked, I then proceeded to use my HiBy R3 as a transmitter and the Hidizs AP80 as as receiver. I logged in into Tidal in the R3 and tested the LDAC codec. It worked! Not only it worked, but the Sample Rate was also adjusted accordingly, meaning that standard 44.1Khz Tidal tracks will be transmitted and received at that very same sample rate. I also tested playing back one of a few Tidal albums that the R3 seems to decode in MQA and the sample rate again was adjusted to 88.2Khz

Here, you can see the HiBy R3 streaming a standard album and transmitting it via LDAC to the Hidizs AP80:

 

 

 

 

 
 
 
View this post on Instagram
 

 

 

 

 

 

 
 

 

 
 

 

 

 

 

 

 

 

 

 

A post shared by Moises Cardona (@moisesmcardona) on

For my next test, I decided to plug in my R3 to my laptop and use Foobar2000 and Tidal in WASAPI mode. This makes the Hiby R3 a USB DAC -> Bluetooth transmitter. This also worked nicely:

 

 

 

 

 
 
 
View this post on Instagram
 

 

 

 

 

 

 
 

 

 
 

 

 

 

 

 

 

 

 

 

A post shared by Moises Cardona (@moisesmcardona) on

Conclusion

I now have the perfect LDAC transmitter and receiver. There’s little delay, but the sound quality is better than using the standard SBC codec. Also it’s worth noting that when I used the HiBy R3 as a USB DAC and LDAC bluetooth transmitter in WASAPI mode, the sample rate was adjusted not only in the R3 but also in the Hidizs AP80, meaning if I’m using a sample rate of 44.1Khz in the PC, the same sample rate will be used in the Hiby R3 and Hidizs AP80. This is very convenient because there will be no downsampling performed. Also, the fact that the Hidizs AP80 also supports bidirectional USB, I could attach another DAC or Amp like the Hidizs DH1000 and enjoy high quality bluetooth sound.

Unboxing and overview of PLUB: Bluetooth Headphone Adapter

Unboxing and overview of PLUB: Bluetooth Headphone Adapter

Hi everyone,

In this post, I’ll show you a video of me unboxing the PLUB, which is a Bluetooth Headphone Adapter.

The Bluetooth adapter features Qualcomm aptX audio codec, so the audio quality is really good compared to the plain old SBC. The way you use this is simply by connecting a headphone/earphone to it.

The adapter also features no buttons except for the Reset one and that’s it. No power up, volume, or multi-function buttons are there. So you may wonder, how does it turn on?

The PLUB works entirely by using your headphone buttons. Just plug it in, and it will power on. Once it’s powered on, you use the headphone buttons to control your device. For example, to change the volume, you just press the headphone volume buttons as you normally would do. To play music, you just press the function button of the headphones. The PLUB effectively recognizes these signals and sends the commands to your devices.

There’s also no USB connection. Then, how do you charge it? Using the same 3.5mm jack! Yup, the PLUB comes with a USB to 3.5mm similar to how the iPod Shuffle would charge. Just plug the 3.5mm into the PLUB and connect the USB cable and let it charge. You can track the progress by checking the LED color.

Yesterday, I received the PLUB in the mail, and you guess what I first did: The Unboxing video.

You can watch it here:

Overall, I’m very satisfied with this device.

I’ll see if I make another video demonstrating how it works because it’s really a simple device and I really like it due to its simplicity.

Hope you enjoyed this video!