Today, I’ll show you the 14TB Western Digital Easystore Hard Disk Drive. This is an external hard drive sold at Best Buy in the United State, and sometimes they sell them at a special price.
The drive comes with a USB 3.0 conection. It has plenty of space to store our precious data as well as allowing us to store backup copies of it. These hard drives are filled with helium which makes them not get too hot when we are using them.
The box comes with a simple presentation, usual of hard disk drives boxes:
When we open it, we see the hard drive:
On the side, we see the cables and the manual:
I connected the drive on Windows which recognized it as a 12.7TB drive. I then went ahead and ran a benchmark using the CystalDiskMark utility. It reported over 200MB+ read/write speed:
Here’s a video of the benchmark, altough I used another drive and it reported over 170MB+. The difference was that this other 14TB drive already had data in it:
With 12.7TB reported on windows, this drive allows us to store huge amounts of data and store backups. It is very fast and comes with typical Western Digital quality. I expect this drive to hold still for a lot of years, as my previous Western Digital drives are still operating excellent.
You can buy this hard disk drive on Best Buy here.
Shucking the Western Digital WD Elements 10TB External Hard Disk Drive
We need to use a sharp object and slide it toward the edges to take off the clips from the case. Then, we’ll slide it to the right carefully:
We’ll keep sliding it right until it gets out:
The drive inside my WD Elements is a WD100EMAZ:
Now, we need to take out the Hard Disk Drive from the case. This is easy, because it is attached to the case using some rubbers. We just need to carefully push the hard drive to get it out:
Now, we need to take out the SATA to USB controller screw:
And here we finally have the shucked drive:
This drive didn’t required any hack to install it in my desktop machine, unlike my 8TB drive which needed to be plugged with a MOLEX to SATA adapter so that it doesn’t receive the 3.3V. I plugged this 10TB drive directly using a SATA power cable from my EVGA 600W PSU:
Windows recognized the drive immediately:
10TB of space! (Actually, 9.1TB)
I ran CrystalDiskMark and this is the result:
It’s fast, and it’s working awesome in my machine.
With this I conclude this quick and simple post.
The Western Digital 10TB WD Elements External Hard Drive
Last week, I got a new Western Digital 10TB Essentials External Drive, which was on sale at $160 on Amazon:
The reason for getting this drive is that in today’s world, digital content is growing by a lot, and files are taking more space than ever. Video resolutions are growing and so are the quality of music, which takes a lot of space. Recent development on newer audio and video codecs may keep the audio file size small, but then, there’s those who store raw or compressed lossless media files, like FLACs or lossless H264/H265 videos.
I myself sometimes record my gameplay when I play Nintendo Switch games, and then I further encode this lossless recording to another HEVC using my NVidia GTX 1060 video card. This saves me between 2 to 5GB of file size. I’m also doing tests encoding my gameplay videos to the newer AV1 codec, that significantly reduces the video size while having a great quality at lower bitrates.
My 8TB drive will soon get full with so many content, encodings, data compression tests, server backups, and so on, hence my reason to add another drive (In reality, half of the disk is full). I found the $160 price very reasonable, considering my 8TB drive was also priced at $160 at Best Buy a few months ago.
When I purchased this drive on Amazon, it was actually not in stock, so I had to wait a few weeks, but it made it home. Here’s the drive box:
Here are the sides:
And the back:
Opening the box, we find the drive well protected:
In the side, we can see the Power Supply and USB 3.0 cable, along with the user manual:
Here’s the drive out of the box in its protected plastic pads:
Here, we can see the drive with the plastic wrap in place:
Here, we can see the drive USB 3.0 and power supply jack, and the power button:
Here are the photos with the wrap taken off:
Here’s the power supply in its bag:
And outside the bag:
The Power Supply has a barrel-type plug:
Next, we have the USB 3.0 cable:
Finally, we have the user manual:
And that concludes this photo session. Later, I’ll do a post shucking this drive and also share the benchmark to you.
Today, I’m sharing a picture of a failed Seagate 5TB Hard Disk Drive. This model is ST5000DM000. This is how it looks internally:
The drive failed prematurely. It looks good. The heads are parked correctly, and it spins up. The problem seems to be in the firmware are of the disk, as it seems to seek but after that, it does a 5 soft clicks before the SATA to USB adapter begins to blink. This HDD was taken out of the external enclosure and was from the Seagate Expansion series.
Unfortunately, Seagate doesn’t covers shucked drives, so I’m out of luck. I don’t remember the warranty, also, but the drive had only 3 years before failing. I remember when Hard Drives would last years! Just as a precaution, I switched to Western Digital. Let’s see how long it lasts.
Have you had a Seagate drive fail on you? Let me know in the comments.
Shucking a Western Digital 8TB My Book External Hard Disk Drive
In today’s post, I’ll be sharing some pictures of my shucked Western Digital 8TB My Book External Hard Disk Drive.
I got this hard drive as I’ve already had 2 other Seagate Hard Drives fail and needed another drive. I changed brands to Western Digital as I’ve been having a bad luck with Seagate lately.
Here’s the drive’s box:
The drive outside of the box:
The front of it:
Here, I’ve taken the drive out of the main enclosure. It still needs to be removed from the internal enclosure:
Finally, here’s removed:
From what I’ve read, this is an HGST Helium-filled hard drive. Western Digital acquired HGST, so this is something that may be accurate. Also, another thing is that you can’t use a SATA power connector that supplies 3.3V. I’ve read reports of this, and they are actually true. It seems that if the drive senses the 3.3V, it disables the unit. This may be to prevent people from taking out the drive from the enclosure and use as an internal hard drive, as it’s actually cheaper to purchase an external drive, shuck it, and install as an internal disk.
The solution that I did was to use a standard MOLEX to SATA power adapter. These cables have 5V, 12V, and 2 ground cables. They do not pass 3.3V, making the drive usable inside the PC.
Privacy & Cookies Policy
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.